![]() ![]() Items NOT INCLUDED with your AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly! The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump has the following Specifications:Ĭlick here for the AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump Parts Break Down. Overall AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump efficiency is increased. Design: Using advanced fluid handling design programs.Mounting Flanges: Gasoline SAE J609a flange.Wet End Repair: Very simple no special tools required.Valve Design: Each AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump series has a valve design that optimizes its highest efficiency.Dyno Proven: All AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump are dyno tested to assure the theoretical design meets the actual design.The oil seals have stainless steel garder springs to assure constant tension on the sealing surface. Oil Seals and O-rings: All are constructed of Buna-N rubber.Crankshaft/Wobble Plate: Precision die-cast to assure proper stroke, duration and alignment.The housing retains the crankshaft bearing, oil seal and rear wobble plate bearing support washer. Rear Cover: Precision die-cast, O-ring sealed.Crankcase: Precision die-cast, large cooling fins and anodized for maximum heat dissipation. ![]() All of the thrust plates are made of heat treated hardened steel for extended life. ![]() Bearings: Angular contact ball bearing stabilizes the crankshaft and one thrust needle bearing absorbs the plunger load and assures long radial plate life.The pump includes a plunger shoe to distribute the additional plunger load. – Plungers: Coated ceramic stainless steel, strong and durable.– Support and Guides: Machined brass, 1-piece construction to assure proper plunger alignment, maximize packing and seal life.– Low-Pressure Seals: “U” cup double lip Buna-N for a good positive seat.Continuously lubricating for extended life, self lubricating packing/Plunger guide support ring. – High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.– Valve Caps: Machined brass for greater strength.– Poppets, Seat and Spring: 303 and 400 series stainless steel.Unique inlet valve configuration: the valve cage incorporates the high pressure packing head ring. – Ultra Form Cages: Durable, strong, and long life.Integral trap pressure, fixed or adjustable chemical injector. – Unloader: Built in to optimize performance while reducing setup time.– Forged Brass: Strength and no porosity – long life.This AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump Features: Integral trap pressure with fixed or adjustable chemical injector. Built-in unloader to optimize performance while reducing setup time. Seals and V-Packings designed to continuously lubricate for extended life. Precision die-cast crankcase with large cooling fins for maximum heat dissipation. The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump has optional vertical and horizontal setups. The AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump spins at 3400 RPM in a direct drive system coupled with a gasoline engine, the matching flange provides convenient connections to most 3/4” shaft 3.5 – 6.5 HP engines. This AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump is designed for medium duty loads. XJV-E22G24D-F7 AR (Annovi Reverberi) Pump 2. PSI AR (Annovi Reverberi) XJV-E22G24D-F7 Pressure Washer Pump ![]()
0 Comments
Leave a Reply. |